UNI-GAIN

Manual v1.0.0 • Plugin v1.0.0

Interface Overview

1 2 3 4

Utility gain and routing

UNI-GAIN 게인, 극성, 채널 스왑, 모노 합산을 처리하는 투명 유틸리티입니다.

상단 브랜드 헤더 아래에 큰 Gain 노브와 dB 표시가 배치되고, 하단 토글로 Phase, Swap, Mono를 빠르게 점검합니다. 기본 운용은 Safety On의 Protected Gain이며, Safety Off는 명시적으로 선택한 Raw Gain 모드입니다.

UNI-GAIN A transparent utility for gain, polarity, channel swap, and mono summing.

A large Gain knob and dB readout sit under the brand header, with Phase, Swap, and Mono toggles below for fast routing checks. The default path is Safety On Protected Gain; Safety Off is an explicit Raw Gain mode.

TruePeakGuardDenormal-safe DSPRealtime/offline QAPhase-aware routing

Interface Operation

1Main Knob

큰 Gain 노브는 플러그인의 중심 레벨을 조절합니다. 위 또는 오른쪽으로 드래그하면 레벨이 올라가고, 아래 또는 왼쪽으로 드래그하면 내려갑니다. 작은 보정은 dB 표시창을 보며 -0.1 dB 단위 감각으로 맞추는 것이 안전합니다.

The large Gain knob controls the main level. Drag up or right to raise level, and down or left to lower it. For small moves, watch the dB readout and trim with a 0.1 dB mindset.

2Value Display

숫자 표시창은 현재 값을 정확한 단위로 보여줍니다. 클릭하면 직접 입력할 수 있고, Enter 또는 포커스 해제로 커밋됩니다. Escape는 편집 전 값으로 되돌립니다. 노브나 표시창을 더블 클릭하면 기본값으로 리셋됩니다.

The value display shows the exact value and unit. Click it to type a value; Enter or blur commits it. Escape restores the previous value. Double-click the knob or display to reset to default.

3Lower Controls

하단 패널은 Phase, Swap, Mono 라우팅 점검 영역입니다. Phase는 극성 반전, Swap은 L/R 교환, Mono는 모노 호환성 확인과 저역 중심 점검에 사용합니다.

The lower panel is the routing check area: Phase flips polarity, Swap exchanges L/R, and Mono checks mono compatibility and low-end focus.

4Mix Slider

오른쪽 세로 Mix 슬라이더는 처리음과 원음의 비율을 정합니다. 위로 올릴수록 처리음이 전면으로 나오고, 아래로 내릴수록 원음의 중심과 transient가 더 많이 남습니다. 트랙 보정은 낮은 Mix가 자연스럽고, 완전한 효과 또는 유틸리티 처리는 100%가 기준입니다.

The vertical Mix slider controls the processed/dry balance. Higher values bring the processed signal forward; lower values keep more dry center and transient identity. Lower Mix is often natural for track enhancement, while full effects or utility use usually starts at 100%.

Quick Start

Workflow

  1. Gain으로 레벨을 먼저 맞춥니다.
  2. Phase와 Swap으로 다중 마이킹 또는 스테레오 라우팅 오류를 점검합니다.
  3. Mono로 저역 중심과 클럽 호환성을 확인합니다.
  4. 기본 Safety On 상태에서 true-peak 보호를 유지하고, 정확한 수학적 Raw Gain 검증이 필요할 때만 DAW 파라미터에서 Safety를 끕니다.
  1. Set the level first with Gain.
  2. Use Phase and Swap to check multi-mic or stereo routing errors.
  3. Use Mono to confirm low-end focus and club compatibility.
  4. Keep the default Safety On true-peak protection, and turn Safety off from the DAW parameter only when exact mathematical Raw Gain verification is required.

Listening Focus

항상 bypass와 같은 라우드니스에서 비교하십시오. 노브를 크게 움직이기보다 소스의 중심, 트랜지언트, 공간 위치가 어떻게 바뀌는지 먼저 확인하는 것이 더 안전합니다.

Always compare against bypass at matched loudness. Instead of making large moves immediately, first listen for changes in source focus, transient shape, and spatial placement.

Signal Flow

InputGain lawPhase/Swap/Mono matrixMixProtected Safety / Raw OffOutput

정확한 레벨 매칭과 라우팅 교정을 위한 투명 경로입니다. 게인 조작은 smoothing을 거쳐 클릭을 줄입니다. Safety On은 true-peak 보호와 내부 headroom 관리를 적용하고, Safety Off는 보호를 우회한 Raw Gain으로 동작합니다.

A transparent path for level matching and routing correction. Gain moves are smoothed to reduce clicks. Safety On applies true-peak protection and internal headroom management; Safety Off bypasses protection for Raw Gain behavior.

Control Map

Gain

-80..+12 dBAutomatable

전체 레벨을 조절합니다. 레퍼런스와 같은 라우드니스에서 비교하면 과한 보정 없이 정확한 gain staging을 만들 수 있습니다.

Controls overall level. Compare at matched loudness to make accurate gain-staging decisions without over-correction.

Phase

toggleAutomatable

극성을 반전해 킥, 베이스, 다중 마이크 소스의 저역 캔슬을 빠르게 확인합니다.

Inverts polarity to quickly check low-end cancellation on kick, bass, or multi-mic sources.

Swap

toggleAutomatable

좌우 채널을 교환해 잘못 녹음되거나 라우팅된 스테레오 이미지를 바로잡습니다.

Swaps left and right channels to correct reversed stereo recordings or routing.

Mono

toggleAutomatable

스테레오 신호를 모노로 접어 중심 에너지와 위상 호환성을 확인합니다.

Folds the stereo signal to mono for center-energy and phase compatibility checks.

Mix

0..100%Automatable

처리 전후를 병렬로 비교합니다. 유틸리티 작업에서는 100%가 기본이며 진단 상황에서만 낮춰 비교합니다.

Blends processed and dry signal. Utility work usually stays at 100%, while lower values help diagnostic comparisons.

Engine Notes

Output Integrity

공통 보호 설계는 단순 샘플 피크뿐 아니라 재구성 피크, 내부 레이턴시 정렬, dry/wet 위상 안정성을 함께 고려합니다. Safety 또는 LIMIT 경로는 true peak ceiling 검증을 기준으로 관리됩니다.

The shared protection design considers reconstructed peaks, internal latency alignment, and dry/wet phase stability. Safety and LIMIT paths are validated against true-peak ceiling behavior.

Session Stability

오디오 스레드는 파라미터 스무딩, denormal flush, hot-path 수학 연산 축소, 실시간/오프라인 렌더 QA를 기준으로 관리됩니다. 긴 세션과 빠른 오토메이션에서도 클릭, CPU 스파이크, true peak 누수를 줄이는 것을 목표로 합니다.

The audio thread is checked for parameter smoothing, denormal flushing, reduced hot-path math, and realtime/offline render QA. The goal is lower click risk, fewer CPU spikes, and controlled true-peak behavior during long sessions and fast automation.

Philosophy & Technology

UNI-GAIN은 현대 믹싱 워크플로우에서 가장 기초적이면서도 필수적인 요소인 '정확한 레벨 컨트롤과 라우팅 유틸리티'를 궁극의 퀄리티로 경험할 수 있게 설계되었습니다.

본 버전은 Gain/Mix/Phase/Swap/Mono/Bypass 경로에 클릭 방지 스무딩을 적용해 급격한 오토메이션에서도 클릭/지퍼 노이즈를 줄였습니다. -80dB에서 +12dB까지의 게인 범위는 비대칭 커브 매핑으로 미세 감쇠와 실무 부스트 구간의 조작성 모두를 확보합니다.

또한 소프트 바이패스 크로스페이드내부 보호 경로 지연 정합을 통해 프로젝트 환경(실시간/오프라인)에서 동작 일관성을 유지합니다. Safety On은 보호된 게인 경로를 사용하고, Safety Off는 보호 개입 없이 설정 dB를 그대로 적용하는 Raw Gain 모드입니다.

UNI-GAIN is rigorously designed to provide the ultimate quality of experience for the most fundamental and essential elements in modern mixing workflows: accurate level control and routing utilities.

This release applies click-safe smoothing across the Gain/Mix/Phase/Swap/Mono/Bypass paths, reducing clicks and zipper artifacts during fast automation. The -80 dB to +12 dB gain range keeps the asymmetric curve mapping for practical fine attenuation and controlled boost moves.

It also uses a soft-bypass crossfade and latency-aligned internal protection path for consistent behavior in both real-time playback and offline rendering. Safety On uses the protected gain path; Safety Off is a Raw Gain mode that applies the requested dB without protection intervention.

Control Guide (How to Use)

Gain

Main Control

역할: 입력 신호의 전체 레벨을 -inf (-80) dB에서 +12 dB 범위 내로 섬세하게 부스트하거나 감쇠합니다.

음향적 변화: 원음의 음색을 전혀 왜곡하지 않는 투명한 디지털 게인 스테이징을 실현합니다. 직관적인 중앙 노브 컨트롤과 고유 스무딩 알고리즘 덕분에 노브를 빠르게 돌려도 음악의 흐름을 방해하는 클릭 노이즈가 발생하지 않으며, 안심하고 자연스러운 페이드 인/아웃 효과나 정밀한 레벨 매칭을 만들어낼 수 있습니다.

빠른 리셋: 노브 또는 dB 표시창을 더블 클릭하면 기본값 0.0 dB로 즉시 복귀합니다.

Role: Delicately boosts or attenuates the overall level of the input signal from -inf (-80) dB to +12 dB.

Acoustic Change: Realizes transparent digital gain staging that does not distort the original tone. Thanks to the intuitive central knob control and proprietary smoothing algorithm, fast knob turns will not generate musical flow-interrupting click noises. You can confidently create natural fade in/out effects and precise level matching.

Quick Reset: Double-click the knob or dB display to instantly return to the default 0.0 dB.

Phase

Utility

역할: 프로세싱되는 오디오 신호의 위상(Polarity)을 180도 반전시킵니다.

음향적 변화: 물리적 거리가 다른 다중 마이킹 트랙(예: 킥/오버헤드 드럼)이나 병렬 프로세싱 시 흔히 발생하는 위상 캔슬레이션(소리의 에너지가 상쇄되는 현상)을 즉각적으로 테스트하고 교정하여 소리를 훨씬 단단하고 펀치감이 살아있게 복원합니다.

Role: Inverts the polarity of the processed audio signal by 180 degrees.

Acoustic Change: Instantly tests and corrects phase cancellation (the loss of sound energy) common in multi-mic tracks with different physical distances (e.g., kick/overhead drums) or parallel processing, restoring the sound to be much tighter and punchier.

Swap

Routing

역할: 스테레오 트랙의 좌측(L)과 우측(R) 채널 피드를 서로 뒤집습니다.

음향적 변화: 밴드 세션이나 신디사이저 트랙에서 좌우 밸런스가 반대로 믹스되거나 녹음되었을 때 케이블이나 트랙 순서를 복잡하게 변경할 필요 없이 한 번에 교정할 수 있으며, 공간감을 의도적으로 비틀어 창의적인 분위기를 연출할 때도 직관적으로 사용됩니다.

Role: Swaps the left (L) and right (R) channel feeds of a stereo track.

Acoustic Change: When the left-right balance is mixed or recorded in reverse on band sessions or synthesizer tracks, it can be corrected at once without having to complexly alter cables or track orders. It's also intuitively used to creatively distort the spatial sense to produce an artistic atmosphere.

Mono

Image

역할: 스테레오의 L과 R 채널 신호를 균등하게 합산하여 완벽한 모노(Mono) 사운드로 병합시킵니다.

음향적 변화: 스테레오 스피커에서 재생되던 와이드한 소리가 정중앙(Center)으로 강력하게 응집됩니다. 킥이나 베이스 트랙의 단단한 저음 에너지를 확보하거나 각종 매체의 스피커에서 소리가 사라지지 않는지 하위 호환성(Mono Compatibility)을 체크할 때 필수적인 기능입니다.

Role: Evenly sums the stereo L and R channel signals, collapsing them into a perfect Mono sound.

Acoustic Change: The wide sound previously played back on stereo speakers powerfully coheres to the Center. It is an indispensable feature for securing the solid low-end energy of kick or bass tracks or checking Mono Compatibility to ensure sounds don't disappear on different media speakers.

Mix

Blend

역할: 아무것도 가공되지 않은 오리지널(Dry) 신호와 게인 및 각종 라우팅이 처리된(Wet) 신호 간의 밸런스를 조절합니다.

음향적 변화: 위상을 뒤집거나 극단적으로 레벨을 조작한 뒤 믹스 슬라이더를 통해 원음과 절묘한 비율로 병렬 프로세싱(Parallel Processing)을 할 수 있습니다. 0%에서 100% 사이를 오가며 볼륨의 질감과 트랜지언트를 다채롭고 자연스럽게 블렌딩합니다.

빠른 리셋: 슬라이더(트랙/핸들)를 더블 클릭하면 기본값 100%로 즉시 복귀합니다.

Role: Adjusts the balance between the unprocessed original (Dry) signal and the processed (Wet) signal with gain and routing changes applied.

Acoustic Change: After inverting the phase or making extreme level adjustments, you can achieve parallel processing at a refined ratio with the original sound using the mix slider. Going back and forth between 0% and 100%, you can colorfully and naturally blend the volume's texture and transients.

Quick Reset: Double-click the mix slider (track or handle) to instantly return to the default 100%.

Parameter Reference (DSP / GUI 일치 기준)

Safety는 실제 C++ 파라미터지만 미니멀 GUI에는 전용 버튼으로 노출되지 않습니다.

Safety is a real C++ parameter, but it is not exposed as a dedicated control in the minimal GUI.

1 2 3 4 5

전체 GUI 캡처에서 번호가 찍힌 위치를 먼저 확인한 뒤, 아래 카드에서 같은 번호의 C++ ID, 범위, 기본값, 동작 설명을 대조하십시오. GUI에 직접 보이지 않는 항목은 Internal로 분리됩니다.

Use the numbered full-interface map first, then match each number with the C++ ID, range, default value, and behavior notes below. Parameters without a visible UI control are marked as Internal.

#1

Gain

C++ ID: gain
Main Knob
Range
-80.0 to +12.0 dB
Default
0.0 dB
GUI
Visible control

레벨 매칭과 gain staging을 위한 메인 dB 컨트롤입니다. -80 dB부터 +12 dB까지 비대칭 커브로 정밀하게 움직입니다.

Main dB control for level matching and gain staging. It spans -80 dB to +12 dB with an asymmetric control curve.

#2

Phase

C++ ID: phase
Toggle Button
Range
Normal / Inverted
Default
Normal
GUI
Visible control

극성을 반전합니다. 다중 마이킹, 병렬 체인, 킥/베이스 위상 점검에서 즉시 비교할 수 있습니다.

Flips polarity for quick multi-mic, parallel-chain, kick/bass phase checks.

#3

Swap

C++ ID: swap
Toggle Button
Range
L/R / R/L
Default
L/R
GUI
Visible control

스테레오 좌우 채널을 교환합니다. 잘못 녹음되거나 뒤집힌 stereo routing을 빠르게 바로잡습니다.

Swaps left and right channels to correct reversed stereo routing quickly.

#4

Mono

C++ ID: mono
Toggle Button
Range
Stereo / Mono
Default
Stereo
GUI
Visible control

L/R을 모노로 합산해 저역 중심, club compatibility, 위상 취소를 확인합니다.

Sums L/R to mono for low-end focus, club compatibility, and phase-cancellation checks.

#5

Mix

C++ ID: mix
Vertical Slider
Range
0.0 to 100.0 %
Default
100.0 %
GUI
Visible control

Gain/routing 처리 경로와 원음을 병렬 비교합니다. 일반적인 유틸리티 작업에서는 100%가 기본입니다.

Blends processed utility path with dry signal. For normal utility use, 100% is the default.

Internal

Safety

C++ ID: safety
DAW / Internal
Range
Off / On
Default
On
GUI
DAW / host only

True-peak 보호 경로를 위한 내부/DAW 파라미터입니다. 기본 On 상태는 Protected Gain으로 동작합니다. Off는 자동 headroom/soft protection/true-peak guard를 우회하는 Raw Gain 모드이며 출력 true peak 초과 가능성을 사용자가 책임집니다.

Internal/DAW parameter for the true-peak safety path. On is the default Protected Gain behavior. Off is Raw Gain mode and bypasses automatic headroom, soft protection, and true-peak guard; the user is responsible for any true-peak overs.

Credits & License

라이선스 / 크레딧 전문 보기Show license / credit details

JUCE Framework
Copyright © Raw Material Software Limited.
라이선스: JUCE EULA(상용) / GPL v3(이중 라이선스).
상업적 비공개 배포에는 JUCE 상용 라이선스가 필요하며, GPL 조건으로 배포할 경우 전체 배포물이 GPL 의무를 충족해야 합니다.

Google Sans Font
Copyright © 2025 The Google Sans Project Authors (github.com/googlefonts/googlesans).
저작권자 표기: Google LLC / Google Sans Authors.
라이선스: SIL Open Font License 1.1. 본 문서 하단에 라이선스 전문을 직접 포함했습니다.

EULA
최종 사용자 라이선스는 서명된 UNI-VERSE macOS 인스톨러에 포함된 통합 EULA를 따릅니다. 본 매뉴얼과 EULA는 플러그인 v1.0.0 기준으로 동기화되었습니다.

법무 감사 로그
plugins/UNI-GAIN/manual/THIRD_PARTY_NOTICES.md 문서에 서드파티 목록/라이선스 상태를 기록합니다.

JUCE Framework
Copyright © Raw Material Software Limited.
License: JUCE EULA (commercial) / GPL v3 (dual-license).
Commercial closed-source distribution requires a JUCE commercial license. If distributed under GPL terms, the full distributed work must comply with GPL obligations.

Google Sans Font
Copyright © 2025 The Google Sans Project Authors (github.com/googlefonts/googlesans).
Attribution owner: Google LLC / Google Sans Authors.
License: SIL Open Font License 1.1. The full license text is embedded directly below.

EULA
End-user license terms are provided by the unified UNI-VERSE EULA included with the signed macOS installer. This manual and EULA are synced to plugin v1.0.0.

Legal audit log
plugins/UNI-GAIN/manual/THIRD_PARTY_NOTICES.md tracks third-party components and licensing status.

SIL Open Font License 1.1 (Google Sans)
This Font Software is licensed under the SIL Open Font License, Version 1.1.
This license is copied below, and is also available with a FAQ at:
https://openfontlicense.org


-----------------------------------------------------------
SIL OPEN FONT LICENSE Version 1.1 - 26 February 2007
-----------------------------------------------------------

PREAMBLE
The goals of the Open Font License (OFL) are to stimulate worldwide
development of collaborative font projects, to support the font creation
efforts of academic and linguistic communities, and to provide a free and
open framework in which fonts may be shared and improved in partnership
with others.

The OFL allows the licensed fonts to be used, studied, modified and
redistributed freely as long as they are not sold by themselves. The
fonts, including any derivative works, can be bundled, embedded,
redistributed and/or sold with any software provided that any reserved
names are not used by derivative works. The fonts and derivatives,
however, cannot be released under any other type of license. The
requirement for fonts to remain under this license does not apply
to any document created using the fonts or their derivatives.

DEFINITIONS
"Font Software" refers to the set of files released by the Copyright
Holder(s) under this license and clearly marked as such. This may
include source files, build scripts and documentation.

"Reserved Font Name" refers to any names specified as such after the
copyright statement(s).

"Original Version" refers to the collection of Font Software components as
distributed by the Copyright Holder(s).

"Modified Version" refers to any derivative made by adding to, deleting,
or substituting -- in part or in whole -- any of the components of the
Original Version, by changing formats or by porting the Font Software to a
new environment.

"Author" refers to any designer, engineer, programmer, technical
writer or other person who contributed to the Font Software.

PERMISSION & CONDITIONS
Permission is hereby granted, free of charge, to any person obtaining
a copy of the Font Software, to use, study, copy, merge, embed, modify,
redistribute, and sell modified and unmodified copies of the Font
Software, subject to the following conditions:

1) Neither the Font Software nor any of its individual components,
in Original or Modified Versions, may be sold by itself.

2) Original or Modified Versions of the Font Software may be bundled,
redistributed and/or sold with any software, provided that each copy
contains the above copyright notice and this license. These can be
included either as stand-alone text files, human-readable headers or
in the appropriate machine-readable metadata fields within text or
binary files as long as those fields can be easily viewed by the user.

3) No Modified Version of the Font Software may use the Reserved Font
Name(s) unless explicit written permission is granted by the corresponding
Copyright Holder. This restriction only applies to the primary font name as
presented to the users.

4) The name(s) of the Copyright Holder(s) or the Author(s) of the Font
Software shall not be used to promote, endorse or advertise any
Modified Version, except to acknowledge the contribution(s) of the
Copyright Holder(s) and the Author(s) or with their explicit written
permission.

5) The Font Software, modified or unmodified, in part or in whole,
must be distributed entirely under this license, and must not be
distributed under any other license. The requirement for fonts to
remain under this license does not apply to any document created
using the Font Software.

TERMINATION
This license becomes null and void if any of the above conditions are
not met.

DISCLAIMER
THE FONT SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT
OF COPYRIGHT, PATENT, TRADEMARK, OR OTHER RIGHT. IN NO EVENT SHALL THE
COPYRIGHT HOLDER BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
FROM, OUT OF THE USE OR INABILITY TO USE THE FONT SOFTWARE OR FROM
OTHER DEALINGS IN THE FONT SOFTWARE.
            

Release & Support

Version: UNI-VERSE v1.0.0 / Plugin v1.0.0
Formats: Audio Unit (AU) and VST3, where supported by the host and platform.
Support: contact@qlaudio.com
EULA: The unified UNI-VERSE EULA is included with the signed macOS installer package.

Version: UNI-VERSE v1.0.0 / Plugin v1.0.0
Formats: Audio Unit (AU) and VST3, where supported by the host and platform.
Support: contact@qlaudio.com
EULA: The unified UNI-VERSE EULA is included with the signed macOS installer package.